Copper Mould Tube & Plate

Copper Mould Tube & Plate
We specially in supplying Copper Mould Tube, Crystallizing equipment of continuous casters, Mould cooling jacket, Repair of Metallurgical Copper Mould Tube, etc.
Equipments & Spare parts for Continuous Casting Machine.
1. Copper mould tube( square, rectangle and round )
2. Crystallizing equipment of continuous casters
3. Mould cooling jacket.
4. repair of copper tube moulds

COPPER MOULD ALLOYS
The copper alloys chosen for the moulds must maintain their physical properties at the operating temperatures of the continuous casting process.
The temperature gradation from the inner wall of the mould to the outside face of the mould can cause serious distortion problems, and Metallurgical Copper Mould Tube is imperative that the correct alloy is chosen for the various operating conditions.

Square Copper mould tube STANDARD MATERIALS
Phosphorus de-oxidised copper
This alloy has been proven to be excellent for the manufacture of moulds in the continuous casting of billets. The main composition of this alloy are Cu +Ag 99.90min, P0.0015 / 0.040.
Copper -Silver alloy
The addition of a small amount of silver, whilst not increasing the melting point of copper, does increase the recrystallisation temperature by almost 100℃, and also helps to give better thermal conductivity at the operating temperatures.
This alloy is normally used in moulds for the continuous casting of blooms and slabs .In this case, the moulds are much thicker than in the billet moulds, and the moulds temperature can be higher. The main composition of this alloy are Cu+Ag99.90 min. Ag 0.08 / 0.12 O 0.004 / 0.012.
Copper Mould Tube supplier
The continuous casting of molten steel into billets, blooms and slab products, has been highly refined over the years into an extremely sophisticated system. The continuous casting process is expected to produce metallurgically sound products at the lower possible cost, and this is being achieved in many steelworks throughout the world.
Copper moulds have played an important role in the development of the continuous casting process. Their funcition is to receive the molten steel and to allow rapid heat transfer from the steel to the cooling water to enable quick solidification.
The mould must exhibit excellent thermal conductivity, be resistant for thermal erosion ,and be resistant to distortion from thermal stress. So far only copper and a few copper alloys meet the above conditions, both economically and technically.
Mould cooling jacket supplier SOLIDIFICATION
The rate of solidification in the continuous casting process dictates the speed of production. The molten steel, which is in contact with the inner faces of the copper mould, starts to sllidify as rapidly as the heat is extracted, forming a shell. The shell increases in thickness as more heat is extracted, and eventually total solidfication is achieved. the process is similar to the solidification of ingots in ingot moulds. In continuous casting, the whole process is speeded up, with the aim to produce and homogeneous shell growth. Consequently, the mould is an important part of the continuous casting process, and the manufactured quality of the mould plays and important role in their length of life.
INNER SURFACE COATINGS
Over the years, Metallurgists and Engineers have been working together to develop better continuous casting moulds. The steel companies require a more economical mould which will give a longer service life. Surface coating of the inner walls of the mould has given the best results to date. Coatings available are Chromium and Nickel plating. Also, a combination of the two give good results on slab casting.
SPECIFICATIONS OF COPPER MOULD
Square Copper mould tube
Square 60 x 60 - 350 x 350 (mm)
Rectangle 120 x 160 - 180 x 300 (mm)
Round Copper Mould tube
Diameter 100-400 (mm)
Size(mm): 90x90, 100x100, 110x110, 115x115, 120x120
130x130, 135x135, 140x140, 143x143, 150x150
155x155, 160x160, 165x165, 175x175, 180x180
200x200, 220x220, 100x170, 100x173, 130x240
150x200, 150x210, 150x220, 160x200, 160x220
150x225, 160x235, 165x225, 175x225, 180x220
200x240, 240x240, 235x235
Radius(mm): 4000, 5000, 5250, 6000, 7000, 7500, 8000, 9000, 10250, 10300, 11000, 12000
Length(mm): 700, 750, 780, 790, 800, 810, 812, 850, 900, 1000

评论

发表评论

此博客中的热门博文

What are Graphite Electrodes and Needle Coke?

图片
  As a   Graphite Electrodes Manufacturer , share with you. Graphite electrodes are the main heating element used in electric arc furnaces, which is a steelmaking process that melts scrap from old cars or old home appliances to produce new steel. The construction cost of an electric arc furnace is cheaper than that of a traditional blast furnace, which is made of iron ore to make steel and is fueled by coking coal. However, steelmaking costs are higher because they use scrap steel and are driven by electricity. Graphite Electrodes The electrode is a part of the furnace cover and is assembled into a cylinder. Then, the current passes through the electrodes, forming a strong arc, melting the scrap. The size of the electrodes varies greatly, but the diameter can reach 0.75 meters (2 and a half feet), and the longest can reach 2.8 meters (9 feet). The largest weighs more than two metric tons. Up to 3 kilograms (6.6 pounds) of graphite electrodes are required to produce one ton of ...
阅读全文

How to Deal With the Details of Graphite Electrode Use?

图片
  As a   Graphite Electrodes Manufacturer , share with you. We need to know that the wet graphite electrode should be dried before use, and the internal thread of the electrode hole should be checked for integrity. When we clean the surface of the spare graphite electrode and the internal thread of the hole with compressed air, there must be no oily water; avoid cleaning with steel wire or metal brush cloth. Graphite Electrodes It is important to carefully screw the connector into the electrode hole of the spare graphite electrode, and screw the electrode strap (graphite strap is recommended) into the electrode hole on the other end of the spare electrode. When lifting the electrode, the cushion is soft to the bottom of one end of the spare electrode assembly connector to prevent ground damage and connector damage; the lifting hook extends to the lifting ring of the lifting device to lift, the lifting electrode is smooth, preventing the electrode from being released from the B...
阅读全文

Do you know the Bending Strength and Average Particle Size of Graphite Electrode Materials?

图片
  As a   Graphite Electrodes Manufacturer , share it with you. The bending strength of graphite electrode materials and the bending strength of graphite electrode materials are a direct reflection of the strength of the material, reflecting the compactness of the internal structure of the material. Graphite block is a kind of artificial graphite, and artificial graphite is made by artificial heating of coke products. Generally, if it is purified to make high purity, or carbon fiber, the added value is high. Graphite rods are often used as electric heating elements in high-temperature vacuum furnaces. The maximum operating temperature can reach 3000℃. It is easy to oxidize at high temperatures.  Graphite Electrodes Except for vacuum, it can only be used in neutral or reducing atmospheres. Its thermal expansion coefficient is small, thermal conductivity is large, resistivity is (8~13)×10-6 Ω·m, processability is better than SiC, MoSi2 rod, high temperature resistance, extre...
阅读全文